Security Alarms AR6000 Podręcznik Użytkownika Strona 26
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
26 SPEKTRUM DX6 • AIRCRAFT PROGRAMMING GUIDE
CHAPTER 3: KEY INPUT AND DISPLAY
Two input keys are located at the lower faceplate of the DX6 transmitter. The keys are used to access and
program the transmitter. Each key can be moved up or down using your thumbs
CHAPTER 4: BATTERY ALARM AND DISPLAY
When the transmitter battery drops below 9.0 volts, the display will start to flash “BAT” and an audible alarm will
sound eight times. This warning indicates a low battery condition and you should land your aircraft immediately.
Note: During the period that the battery alarm is flashing, the input buttons will not function. If
you are currently in the function mode, the transmitter will exit automatically and return to the
normal display.
THROTTLE CUT
Your DX6 incorporates a special THROTTLE CUT function. The throttle cut button is located on the upper right
face of the transmitter. This feature is designed primarily for glow-powered aircraft and is designed to shut off
the engine when pressed without affecting the throttle trim position. With the throttle stick in the low position,
pressing the throttle cut button with drive the throttle servo to its programmed low throttle, low trim endpoint
adjusted in travel adjust. This will not be a commonly used feature for parkflyer aircraft.
Note: The Throttle Cut function is designed to function only when the throttle stick is below the
1/2 position.
- 6-Channel, 10-Model Memory 1
- DSM Parkflyer and 1
- Micro Helicopter System 1
- Parkflyers Only 2
- How DSM Works 2
- Table of Contents 3
- Alternate Languages 3
- Aircraft Programming Guide 4
- Helicopter Programming Guide 5
- Warranty 5
- Model Type Selection 6
- Digital Trim Settings 10
- Servo Reversing 10
- Travel Adjustment 11
- Pitch Curve 12
- Throttle Curve 13
- User Guide 14
- 15
- Servo Specifications 16
- Charging the Transmitter 17
- Operating the Trainer System 18
- SPEKTRUM DX6 • INTRODUCTION 19
- DIGITAL TRIM LEVERS 21
- RECEIVER CHANNEL ASSIGNMENT 21
- 22
- HOW TO RANGE TEST THE SYSTEM 23
- HOW TO BIND 24
- CHAPTER 2: CONNECTIONS 25
- THROTTLE CUT 26
- NORMAL DISPLAY 27
- DIRECT TRIM ACCESS DISPLAY 27
- SYSTEM MODE 28
- FUNCTION MODE 29
- MODEL TYPE SELECTION 30
- DATA RESET 31
- DUAL RATE SWITCH SELECTION 32
- WING TYPE SELECTION 33
- FLAPERON SETUP 33
- DELTA-WING MIXING 35
- MODEL SELECTION 36
- MODEL NAME ENTRY 37
- SERVO REVERSING 38
- DUAL RATE 39
- EXPONENTIAL 40
- SUB-TRIM 41
- TRAVEL ADJUSTMENT 42
- AILERON-TO-RUDDER MIXING 43
- 4. To exit, press the 44
- ELEVATOR-TO-FLAP MIXING 45
- DIFFERENTIAL 47
- FLAP-TO-ELEVATOR OFFSET TRIM 48
- PROGRAMMABLE MIXING (A, B, C) 49
- ASSIGNING CHANNELS 50
- SWITCH SELECTION 50
- MIXING VALUE ADJUSTMENT 51
- MIXING OFFSET ADJUSTMENT 52
- ACCESSING THE OFFSET FUNCTION 52
- CHAPTER 8: Data Sheet 55
- KEY INPUT AND DISPLAY 62
- GEAR/GYRO SWITCH SELECTION 69
- IMPORTANT GYRO INFORMATION 69
- CHAPTER 7: Function Mode 72
- THROTTLE HOLD 77
- PITCH CURVE 78
- THROTTLE CURVE 80
- REVOLUTION MIXING 82
- PROGRAMMABLE MIXING (A) 83
- CCPM SWASHPLATE MIXING 88
- 89
- CCPM SERVO LOCATIONS 90
- CCPM SERVO CONNECTIONS 91
- One Year Warranty 93
- FCC Information 94
- 95SPEKTRUM DX6 • WARRANTY 95
- SPMM** #8259 96
Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Security Alarms AR6000
(14 strony)
(3 strony)Hanna Instruments HI 84529 manuals
Owner’s manuals and user’s guides for Measuring instruments Hanna Instruments HI 84529.
We providing 1 pdf manuals Hanna Instruments HI 84529 for download free by document types: User Manual
Komentarze do niniejszej Instrukcji